Bronze C93200 Round Bar Weight
Mass per metre and per foot for bronze c93200 round bar at 8,800 kg/m³ (ASTM B505 (UNS C93200, bearing bronze)). Every figure is for the section as drawn. A 6 m length of this size weighs 25.9 kg (58.1 lb per 20 ft).
At the reference dimensions (d = 25 mm) this section has a cross-sectional area of 490.9 mm², giving 4.320 kg/m (2.903 lb/ft). Against carbon steel's 7,850 kg/m³ that is +12.1 % — the same section in steel would be 3.853 kg/m.
Round Bar — formula and derivation
Area of a round bar
A = π/4 · d²
A = π/4 × d², where d is the outside diameter
Worked through with the default dimensions:
A = π/4 × d²A = 0.785398 × 25²A = 0.785398 × 625.0A = 490.9 mm²
- d
- Diameter — Outside diameter measured across the bar.
Weight follows from the area with no further geometry: m = A × 10⁻⁶ × ρ, where A is in mm², ρ in kg/m³ and m in kg/m. At 8,800 kg/m³ that is 4.3197 kg/m for the reference size above.
Bronze round bar — size series
| Diameter | Cross-section | Mass / length |
|---|---|---|
| 6.0 mm | 28.27 mm² · 0.0438 in² | 0.249 kg/m · 0.167 lb/ft |
| 8.0 mm | 50.27 mm² · 0.0779 in² | 0.442 kg/m · 0.297 lb/ft |
| 10 mm | 78.54 mm² · 0.1217 in² | 0.691 kg/m · 0.464 lb/ft |
| 12 mm | 113.10 mm² · 0.1753 in² | 0.995 kg/m · 0.669 lb/ft |
| 14 mm | 153.94 mm² · 0.2386 in² | 1.355 kg/m · 0.910 lb/ft |
| 16 mm | 201.06 mm² · 0.3116 in² | 1.769 kg/m · 1.189 lb/ft |
| 20 mm | 314.16 mm² · 0.4869 in² | 2.765 kg/m · 1.858 lb/ft |
| 25 mm | 490.87 mm² · 0.7609 in² | 4.320 kg/m · 2.903 lb/ft |
| 30 mm | 706.86 mm² · 1.0956 in² | 6.220 kg/m · 4.180 lb/ft |
| 32 mm | 804.25 mm² · 1.2466 in² | 7.077 kg/m · 4.756 lb/ft |
| 40 mm | 1,256.64 mm² · 1.9478 in² | 11.058 kg/m · 7.431 lb/ft |
| 50 mm | 1,963.50 mm² · 3.0434 in² | 17.279 kg/m · 11.611 lb/ft |
| 60 mm | 2,827.43 mm² · 4.3825 in² | 24.881 kg/m · 16.720 lb/ft |
| 80 mm | 5,026.55 mm² · 7.7912 in² | 44.234 kg/m · 29.724 lb/ft |
| 100 mm | 7,853.98 mm² · 12.1737 in² | 69.115 kg/m · 46.443 lb/ft |
Computed for Bronze at 8800 kg/m³ (0.3179 lb/in³). ASTM B505 (UNS C93200, bearing bronze).
Each row is one nominal size. Because the area is computed from your dimensions rather than read from a mill table, a non-standard size is just as accurate — put it into the calculator above rather than interpolating between rows.
Imperial sizes
Round Bar is also bought in inch sizes. The conversions below are exact (1 in = 25.4 mm by definition), so the metric equivalents are the true millimetre dimensions rather than a rounded nominal figure.
| Stock size | Metric equivalent mm | Cross-section | Mass / length |
|---|---|---|---|
| 1/8 in | 3.17 | 7.92 mm² · 0.0123 in² | 0.070 kg/m · 0.047 lb/ft |
| 3/16 in | 4.76 | 17.81 mm² · 0.0276 in² | 0.157 kg/m · 0.105 lb/ft |
| 1/4 in | 6.35 | 31.67 mm² · 0.0491 in² | 0.279 kg/m · 0.187 lb/ft |
| 5/16 in | 7.94 | 49.48 mm² · 0.0767 in² | 0.435 kg/m · 0.293 lb/ft |
| 3/8 in | 9.52 | 71.26 mm² · 0.1104 in² | 0.627 kg/m · 0.421 lb/ft |
| 1/2 in | 12.70 | 126.68 mm² · 0.1963 in² | 1.115 kg/m · 0.749 lb/ft |
| 5/8 in | 15.88 | 197.93 mm² · 0.3068 in² | 1.742 kg/m · 1.170 lb/ft |
| 3/4 in | 19.05 | 285.02 mm² · 0.4418 in² | 2.508 kg/m · 1.685 lb/ft |
| 7/8 in | 22.22 | 387.95 mm² · 0.6013 in² | 3.414 kg/m · 2.294 lb/ft |
| 1 in | 25.40 | 506.71 mm² · 0.7854 in² | 4.459 kg/m · 2.996 lb/ft |
| 1-1/4 in | 31.75 | 791.73 mm² · 1.2272 in² | 6.967 kg/m · 4.682 lb/ft |
| 1-1/2 in | 38.10 | 1,140.09 mm² · 1.7671 in² | 10.033 kg/m · 6.742 lb/ft |
| 2 in | 50.80 | 2,026.83 mm² · 3.1416 in² | 17.836 kg/m · 11.985 lb/ft |
| 2-1/2 in | 63.50 | 3,166.92 mm² · 4.9087 in² | 27.869 kg/m · 18.727 lb/ft |
| 3 in | 76.20 | 4,560.37 mm² · 7.0686 in² | 40.131 kg/m · 26.967 lb/ft |
| 4 in | 101.60 | 8,107.32 mm² · 12.5664 in² | 71.344 kg/m · 47.941 lb/ft |
Stock sizes in inches, converted exactly at 25.4 mm per inch. Material: Bronze C93200 at 8800 kg/m³.
The same round bar in every material
Geometry is fixed and only density changes, so this table is the whole material-selection question in one view. Bronze C93200 is highlighted. The percentage column is against carbon steel, which is the figure most quotations are built on.
| Material | Density kg/m³ | lb/in³ | Mass / length kg/m | lb/ft | vs carbon steel |
|---|---|---|---|---|---|
| Carbon Steel | 7,850 | 0.2836 | 3.853 | 2.589 | +0.0 % |
| Stainless Steel 304 | 8,000 | 0.2890 | 3.927 | 2.639 | +1.9 % |
| Stainless Steel 316 | 8,000 | 0.2890 | 3.927 | 2.639 | +1.9 % |
| Stainless Steel 316L | 8,000 | 0.2890 | 3.927 | 2.639 | +1.9 % |
| Stainless Steel 430 | 7,700 | 0.2782 | 3.780 | 2.540 | -1.9 % |
| Aluminum 6061-T6 | 2,700 | 0.0975 | 1.325 | 0.891 | -65.6 % |
| Aluminum 5052-H32 | 2,680 | 0.0968 | 1.316 | 0.884 | -65.9 % |
| Aluminum 7075-T6 | 2,810 | 0.1015 | 1.379 | 0.927 | -64.2 % |
| Copper C11000 | 8,940 | 0.3230 | 4.388 | 2.949 | +13.9 % |
| Brass C36000 | 8,500 | 0.3071 | 4.172 | 2.804 | +8.3 % |
| Bronze C93200 | 8,800 | 0.3179 | 4.320 | 2.903 | +12.1 % |
| Titanium Grade 2 | 4,510 | 0.1629 | 2.214 | 1.488 | -42.5 % |
| Gray Cast Iron | 7,200 | 0.2601 | 3.534 | 2.375 | -8.3 % |
| Lead | 11,340 | 0.4097 | 5.567 | 3.741 | +44.5 % |
| Rigid PVC (Type I) | 1,400 | 0.0506 | 0.687 | 0.462 | -82.2 % |
| HDPE (PE 100) | 960 | 0.0347 | 0.471 | 0.317 | -87.8 % |
Same geometry throughout, so the only variable is density. Carbon steel is highlighted as the baseline.
A note on using this table for costing: mass is not price. Aluminium is roughly a third of steel's mass here, but per kilogram it costs several times more, so a straight swap rarely saves money — what it buys is reduced load on a structure or a vehicle.
About bronze c93200
Tin-lead bearing bronze, the standard material for plain bushes and wear plates because its microstructure carries a soft lead phase that acts as a built-in lubricant. At 8,800 kg/m³ it sits between copper and brass, and being a cast alloy its density genuinely varies more than the wrought metals — 8,700 to 9,000 kg/m³ is normal across bronze chemistries, so a take-off on a large cast bush should come from the caster’s certificate, not from a table.
- Density
- 8,800 kg/m³ = 0.3179 lb/in³ · 1.1210× carbon steel · typical spread ±3 %
- Specification
- ASTM B505 (UNS C93200, bearing bronze)
- Equivalents
- SAE 660 · EN CW458K · GB ZQSn6-6-3
- Typical uses
- Plain bearings and bushes · Worm gears · Pump and valve components · Wear plates
Cast alloys carry higher density uncertainty than wrought. Typical spread 8,700–9,000 kg/m³.
About round bar
Round bar is the only shape whose area grows with the square of a single dimension, so small diameter changes move weight much faster than intuition suggests: going from 25 mm to 28 mm — a 12 % diameter increase — raises the weight per metre by 25 %. This is why shaft stock is normally bought to the nearest preferred diameter rather than machined down from the next size up; the material saved is more than the weight table implies.
Specified by diameter only. For ground and polished stock, add the tolerance class and the straightness limit.
Download this data
Bronze round bar — CSV
Both buttons below read the tables rendered on this page, so the file matches what you are looking at. The full catalogue — all 16 materials across all 10 sections — is on the downloads page.
Fields are quoted per RFC 4180, with a UTF-8 byte-order mark so Excel reads the mm² and · characters correctly. Blank lines separate the weight matrix from the area matrix.
Frequently asked questions
How much does bronze c93200 round bar weigh?
At the reference dimensions (d = 25 mm) a bronze c93200 round bar of this size weighs 4.320 kg/m, or 2.903 lb/ft. The table above lists the figure for every standard size so you can read your size directly instead of scaling.
How is the weight of round bar calculated?
Weight is cross-sectional area × length × density. For this shape the area is A = π/4 · d². At the reference dimensions that gives 490.9 mm², and multiplying by bronze c93200's density of 8,800 kg/m³ gives 4.320 kg/m. Nothing is looked up in a table — which is why a non-standard size is calculated just as accurately as a standard one.
Why does bronze c93200 weigh more or less than steel?
It is heavier than carbon steel for the same section — about 12 % heavier at 8,800 kg/m³. Density is the only variable: the cross-sectional area depends purely on geometry, so a round bar of the same dimensions has the same area in every material and the mass simply scales with density. In this case the ratio is 1.1210× carbon steel.
What is the cross-sectional area of a round bar?
The area depends only on the dimensions, not on the material, so it is identical whichever material you select: at the reference dimensions it is 490.9 mm² (0.7609 in²). That is the number you would enter into a stress or deflection calculation, and it is why changing material on this page never changes the area column.
Does a bronze round bar weigh the same as a bronze part of a different shape?
No, and the difference is larger than most people expect. At equal nominal size, a square bar is 27.3 % heavier than a round bar, and a hollow section is typically 60–80 % lighter than the solid bar it replaces. Weight follows area, and area changes faster than dimensions do — which is exactly why this needs calculating rather than estimating.
Should I use Bronze weight or carbon steel weight for costing?
Use the material you are actually buying. At 8,800 kg/m³ against carbon steel's 7,850 kg/m³, the same round bar differs by 12.1 % in mass. On a per-metre quote that is invisible; on a fabricated tonnage it is the difference between a margin and a loss. This page computes the steel figure as 3.853 kg/m for comparison.
Other materials, same round bar
The same geometry in every material, so the only variable is density.
- Carbon steel round bar — 7850 kg/m³
- SS 304 round bar — 8000 kg/m³
- SS 316 round bar — 8000 kg/m³
- AL 6061 round bar — 2700 kg/m³
- Copper round bar — 8940 kg/m³
- Brass round bar — 8500 kg/m³
- HDPE round bar — 960 kg/m³
- PVC round bar — 1400 kg/m³
Other Bronze sections
The same density applied to every shape the site covers.
- Bronze square bar — A = a²
- Bronze hexagonal bar — A = (√3/2) · AF² ≈ 0.8660 · AF²
- Bronze flat bar — A = w · t
- Bronze plate — A = w · t
- Bronze round tube — A = π/4 · (D² − d²), d = D − 2t
- Bronze square tube — A = a² − (a − 2t)²
Reference data and tools
- Metal weight overview — how the calculation works
- All 16 materials — densities and specifications
- All 10 sections — formulas and size series
- Density chart — lightest to heaviest
- Metal weight calculator — any size, any material
- All calculators — metal weight and pipe weight
- Download the data — CSV, generated from the same source
- Cross-reference tables — DN / NPS / material equivalents
- Methodology and sources — where every number comes from
Round Bar area from A = π/4 · d². Mass computed as area × length × density at 8,800 kg/m³ (ASTM B505 (UNS C93200, bearing bronze)). No weight on this page is copied from a published table — which is why figures can differ in the last significant digit from a mill's chart calculated at a nominal density.
- Elementary plane geometry. The circle, polygon and hollow-section area formulas.
- ASTM material specifications for each grade named in the material entry (A36, A240/A276, B209/B211/B221, B152/B16/B505, B265/B348, A48, B29, D1784, D3350).
- BIPM / NIST definitional constants: international inch = 25.4 mm, foot = 0.3048 m, pound = 0.45359237 kg.
Dataset version 2026.09.1 · dimensions last verified against source 2026-09-21. Found an error? Report it — corrections are issued with a version bump.